FIN Rear-Edge Tapping Motor Jam

Error code
  • 131 FIN Rear-Edge Tapping Motor Jam
Floor Finisher
Occurrence condition
  • FIN Rear-edge Tapping Motor does not detect changes in IN FIN Rear-edge Tapping Sensor even after a certain amount of time has passed in the direction of HP sensor fluctuation.
Assumed cause
  • FIN Rear-edge Tapping Unit  dirty, deformed, or not fitted properly
  • FIN Rear-edge Tapping Sensor dirty, missing or defective
  • FIN Rear-edge Tapping Motor dirty, missing or defective
  • Floor Finisher main board failure
Related parts
  • FIN Rear-edge Tapping Unit
  • FIN Rear-edge Tapping Sensor
  • FIN Rear-edge Tapping Motor
  • Floor Finisher main board failure
Troubleshooting

Step

Confirmation and action

YES

NO
1

Checking FIN Rear-edge Tapping Unit

Is the FIN Rear-edge Tapping Unit installed properly?

Or is it dirty, deformed or worn?

Clean FIN Rear-edge Tapping Unit

Replace if not repaired

Go to step 2
2

FIN Rear-edge Tapping SensorCheck the connection of the connector

Are the IIN FIN Rear-edge Tapping Sensor connected properly?

 Go to step 3 reconnect IN FIN Rear-edge Tapping Sensor
3

FIN Rear-edge Tapping SensorOperation Check

Is the FIN Rear-edge Tapping Sensor operating normally in the diagnostics menu?

 Go to step 4 Replace FIN Rear-edge Tapping Sensor
4

FIN Rear-edge Tapping MotorCheck the connection of the connector

Are the FIN Rear-edge Tapping Motor connected properly?

 Go to step 5 reconnect FIN Rear-edge Tapping Motor
5

FIN Rear-edge Tapping MotorOperation Check

Is the FIN Rear-edge Tapping Motor operating normally in the diagnostics menu?

 Go to step 6 Replace FIN Rear-edge Tapping Motor
6

Replacing floor finisher main board

Have you reconnected and repaired the connector on the floor finisher main board?

 End Replace floor finisher main board


Inner Finisher
Occurrence condition
  • IN FIN Rear-edge Tapping Motor does not detect changes in IN FIN Rear-edge Tapping Sensor even after a certain amount of time has passed in the direction of HP sensor fluctuation.
Assumed cause
  • FIN Rear-edge Tapping Unit  dirty, deformed, or not fitted properly
  • FIN Rear-edge Tapping Sensor dirty, missing or defective
  • FIN Rear-edge Tapping Motor dirty, missing or defective
  • Finisher main board failure
Related parts
  • Checking FIN Rear-edge Tapping Unit
  • IN FIN Rear-edge Tapping Sensor
  • FIN Rear-edge Tapping Motor
  • Inner Finisher Main Board
Troubleshooting

Step

Confirmation and action

YES

NO
1

Checking IN FIN Rear-edge Tapping Unit

Is the IN FIN Rear-edge Tapping Unit installed properly?

Or is it dirty, deformed or worn?

Clean IN FIN Rear-edge Tapping Unit

Replace if not repaired

Go to step 2
2

IN FIN Rear-edge Tapping SensorCheck the connection of the connector

Are the IN FIN Rear-edge Tapping Sensor connected properly?

 Go to step 3 reconnect IN FIN Rear-edge Tapping Sensor
3

IN FIN Rear-edge Tapping SensorOperation Check

Is the IN FIN Rear-edge Tapping Sensor operating normally in the diagnostics menu?

 Go to step 4 Replace IN FIN Rear-edge Tapping Sensor
4

IN FIN Rear-edge Tapping MotorCheck the connection of the connector

Are the IN FIN Rear-edge Tapping Motor connected properly?

 Go to step 5 reconnect IN FIN Rear-edge Tapping Motor
5

IN FIN Rear-edge Tapping MotorOperation Check

Is the IN FIN Rear-edge Tapping Motor operating normally in the diagnostics menu?

 Go to step 6 Replace IN FIN Rear-edge Tapping Motor
6

Replacing the inner finisher main board

Have you reconnected and repaired the connector on the inner finisher main board?

 End Replace Inner finisher main board