FIN Alignment Rear Jam
Error code
- 114 FIN Alignment Rear Jam
Floor Finisher
Occurrence condition
- FIN Alignment Plate Rear HP Sensor OFF is not detected even after the specified time has passed since the FIN Width Adjustment Rear motor was ON during initial operation.
Assumed cause
- FIN Post-Alignment Plate Guide dirty, deformed, or not fitted properly .
- FIN Post-Alignment Plate HP Sensor dirty, missing or defective
- FIN Alignment Plate Rear Motor dirty, missing or defective
- Floor Finisher main board failure
Related parts
- FIN Post-Alignment Guide
- FIN Alignment Plate Rear HP Sensor
- FIN After Width Alignment Motor
- Floor Finisher main board failure
Troubleshooting
Step |
Confirmation and action |
YES |
NO |
|---|---|---|---|
| 1 | Checking FIN Post-Alignment Plate Is the FIN Post-Alignment Plate installed properly? Or is it dirty, deformed or worn? |
Clean FIN Post-Alignment Plate Replace if not repaired |
Go to step 2 |
| 2 | Checking the FIN Alignment Plate Rear HP Sensor Are the FIN Alignment Plate Rear HP Sensor connected properly? |
Go to step 3 | Reconnect FIN Alignment Plate Rear HP Sensor. |
| 3 | Operation check of FIN Alignment Plate Rear HP Sensor Is the FIN Alignment Plate Rear HP Sensor operating normally in the diagnostics menu? |
Go to step 4 | Replace FIN IN Alignment Plate Rear HP Sensor. |
| 4 | Checking the FIN Width Alignment Rear Motor Are the FIN Width Adjustment Rear Motor connected properly? |
Go to step 5 | Reconnect FIN Width Alignment Front Motor. |
| 5 | Operation check of FIN Width Alignment Rear Motor Is the FIN Width Adjustment Rear Motor operating normally in the diagnostics menu? |
Go to step 6 | Replace FIN Width Adjustment Rear Motor. |
| 6 | Replacing floor finisher main board Have you reconnected and repaired the connector on the floor finisher main board? |
End | Replace floor finisher main board |
Inner Finisher
Occurrence condition
- IN FIN Alignment Plate Rear HP Sensor OFF is not detected even after the specified time has passed since the FIN Width Adjustment Rear motor was ON during initial operation.
Assumed cause
- IN FIN Post-Alignment Plate dirty, deformed, or not fitted properly .
- IN FIN Post-Alignment Plate HP Sensor dirty, missing or defective
- IN FIN Width Adjustment Rear Motor dirty, missing or defective
- Inner Finisher main board failure
Related parts
- IN FIN Alignment Plate Rear Guide
- IN FIN Alignment Plate Rear HP Sensor
- IN FIN Width Adjustment Rear Motor
- Inner Finisher Main Board
Troubleshooting
Step |
Confirmation and action |
YES |
NO |
|---|---|---|---|
| 1 | Checking IN FIN Alignment Plate Rear Guide Is the IN FIN Alignment Plate Rear Guide installed properly? Or is it dirty, deformed or worn? |
Clean FIN Post-Alignment Plate Replace if not repaired |
Go to step 2 |
| 2 | Checking the IN FIN Alignment Plate Rear HP Sensor Are the IIN FIN Post-Alignment Plate HP Sensor connected properly? |
Go to step 3 | Reconnect IN FIN Post-Alignment Plate HP Sensor |
| 3 | Operation check of IN FIN Alignment Plate Rear HP Sensor Is the IN FIN Post-Alignment Plate HP Sensor operating normally in the diagnostics menu? |
Go to step 4 | Replace IN FIN Post-Alignment Plate HP Sensor |
| 4 | Checking the IN FIN Width Adjustment Rear Motor Are the IN FIN Width Adjustment Rear Motor connected properly? |
Go to step 5 | Reconnect the IN FIN Width Adjustment Rear Motor. |
| 5 | Operation check of IN FIN Width Adjustment Rear Motor Is the IN FIN Width Adjustment Rear Motor operating normally in the diagnostics menu? |
Go to step 6 | Replace the N FIN Width Adjustment Rear Motor. |
| 6 | Replacing the inner finisher main board Have you reconnected and repaired the connector on the inner finisher main board? |
End | Replace Inner finisher main board |