FAX Service Parameter Table
| Error code | The panel displayed | Error description | Communication type | Phase | |
|---|---|---|---|---|---|
| Result of communication report | Job history | ||||
| No tone | Failure 203 | No dial tone detected |
Dial tone cannot be detected when dialing. |
TX | A |
| Busy | Failure 204 | Speaking |
Busy tone detected when dialing. |
TX | A |
| no reply | Failure 205 | Fax signal from destination machine cannot be detected after dialing. | TX | A | |
| Port inversion | Failure 206 | |
Before calling (on hook) there was a line voltage but the line voltage was gone when calling (on hook). | TX | A |
| The line is not connected. | Failure 207 | Not properly connected to phone line |
The line voltage is not detected before calling. | TX | A |
| 012 | Failure 202 | Received document length exceeds the maximum value | RX | C | |
| 212 | Failure 202 | (Modem): Data transmission end error | RX/TX | ||
| 220 | Failure 202 | MCF was not sent after receiving data | RX | D | |
| 400 | Failure 202 | T1 timer timed out | TX | B | |
| 401 | Failure 202 | Received a DCN after sending DCS. | TX | B | |
| 402 | Failure 202 | Received a DCN during sending the phase B. | TX | B | |
| 403 | Failure 202 | Receiver dose not have polling sending capability. | RX(POL) | B | |
| 404 | Failure 202 | No response after sending DCS. | TX | B | |
| 405 | Failure 202 | Fall back is not possible in sending. | TX | B | |
| 406 | Failure 202 | A DCN is sent after receiving DCS/DTC. | RX/TX(POL) | B | |
| 407 | Failure 202 | No response or received a DCN after sending Post-command. | TX | D | |
| 408 | Failure 202 | Received a RTN. | TX | D | |
| 409 | Failure 202 | Received a PIN. | TX | D | |
| 410 | Failure 202 | Received a DCN during receiving phase D. | RX | D | |
| 411 | Failure 202 | Received a DCN after sending DTC. | RX(POL) | B | |
| 412 | Failure 202 | Cannot receive DSN after sending FTT. | RX | B | |
| 414 | Failure 202 | No response after DTC transmission | RX(POL) | B | |
| 415 | Failure 202 | No document for polling sending. | TX(POL) | B | |
| 416 | Failure 202 | Cannot receive Post-command | RX | D | |
| 417 | Failure 202 | Sent RTN | RX | D | |
| 420 | Failure 202 | T1 timer timed out | RX | B | |
| 422 | Failure 202 | Settings of DIS/DTC are disabled. | TX | B | |
| 427 | Failure 202 | Received a DCN after sending DIS | RX | B | |
| 433 | Failure 202 | (Modem): Frame length error | RX/TX | B,D | |
| 434 | Failure 202 | (Modem): Frame wait timeout | RX/TX | B,D | |
| 436 | Failure 202 | Received a DCN after sending CFR/FTT | RX | C | |
| 438 | Failure 202 | A DCN is sent after receiving DCS/DTC. |
RX/TX(POL) | B | |
| 459 | Failure 202 | Training error occurred during receiving PIX | RX | C | |
| 490 | Failure 202 | Number of error line exceeds the limit value when receiving PIX. | RX | C | |
| 494 | Failure 202 | (Modem): Timeout between EOL | RX | C | |
| 495 | Failure 202 | Carrier disconnected during receive face C |
RX | C | |
| 496 | Failure 202 | (Modem): Data transmission start error | TX | B,C | |
| 501 | Failure 202 | (V.34) Modem mismatch error | V.34RX/TX | B | |
| 502 | Failure 202 | (V.34) Primary channel end error | V.34RX/TX | C | |
| 503 | Failure 202 | (V.34) Control channel start error | V.34RX/TX | B,C,D | |
| 504 | Failure 202 | (V.34) Polling sending request is rejected in step V.8 | RX(POL) | B | |
| 505 | Failure 202 | (V.34) Rejected the polling sending request in step V.8 | TX(POL) | B | |
| 540 | Failure 202 | (ECM) No response or received a DCN after sending CTC | TX | D | |
| 541 | Failure 202 | (ECM) No response or received a DCN after sending EOR | TX | D | |
| 542 | Failure 202 | (ECM) No response or received a DCN after sending RR | TX | D | |
| 543 | Failure 202 | (ECM) T5 timer timeout | TX | D | |
| 544 | Failure 202 | (ECM) Sent DCN after sending EOR. | TX | D | |
| 550 | Failure 202 | (ECM) (modem): timeout between frames | RX | C | |
| 554 | Failure 202 | (ECM) ERR was sent after receiving EOR | RX | D | |
| 580 | Failure 202 | The receiver dos not have F code (password) capability. | TX | B | |
| 582 | Failure 202 | The receiver (polling sending) dos not have F code (password) capability. | RX(POL) | B | |
| 826 | Failure 202 | SUB / SID or SEP / PWD did not match | RX/TX(POL) | B | |
| F0B | Failure 202 | Error only during multiport transmission, or no transmission channel error *Occurs when a receive-only channel is designated and the designated channel has failed. |
TX | B | |