# FAX Service Parameter Table

On/Off

Set the lower limit / upper limit of the ringing signal detection frequency.
When connecting line = PSTN, detection is performed in the range of 12 to 66Hz by default.

11 to 21

Set the lower limit / upper limit of the ringing signal detection frequency.
When connecting line = PBX, detection is performed in the range of 11 to 80Hz by default.

Minimum time to detect IR ON.
When the set value is shorter than this, the product does not detect IR and response an incoming call. (A calling tone rings with ON of 80ms.)

Maximum time to detect IR ON.
When the set value is longer than this, the product does not detect IR and response an incoming call. (A calling tone rings.)

Duration time to detect IR OFF
When a IR OFF TIME longer than the set value is detected, counts one IR.
It does not count when the OFF TIME is shorter. Line type = the reference value for PSTN

When a OFF Time is longer than this, judges that IR is disappeared.
Resets IR counter. Display of during calling disappears.

Duration time to detect IR OFF
When a IR OFF TIME longer than the set value is detected, counts one IR. It does not count when the OFF TIME is shorter.
Line type = the reference value for PBX

Dial type

Tone/10PPS/20PPS

Changes the wait time of pause inputted with PAUSE button used to register a fax number to contact list.

Changed when the wait time exceeds the set time because receiver’s response is slow.
This has the same effect as entering a pause with PAUSE button after dialing.

When performing broadcast fax, set this shorter for sending only, and set this longer for sending and receiving to make space for a incoming call.
Change the “038 JOB INTERVAL TIME” as well.

Adjusts Send time/Inter-digit time for sending DTMF (Tone). Dial speed is made faster by lowering the set value.
Note that if it is set too fast, failures in dial tone detection or connection may occur.
70-70ms or longer is recommended.
Make sure to perform dial check test after the change to confirm the connection.

On/Off

If there is no problem with the telephone line and the connection of the telephone line, but the error of “Automatic line check function” causes “line not connected” or “line reverse insertion” error, set to Off.

In the initial setting, when a dial tone is detected for 1000 ms (1 s), it is determined that a dial tone exists.
* Dial tone detection waiting time is fixed at 10s.

Dial tone off ignore time (PSTN)

The dial tone off time of this set value is regarded as the dial tone continuation.
Connection line = PSTN

Dial tone off ignore time (PBX)

The dial tone off time of this set value is regarded as the dial tone continuation.
Connection line = PBX

Pause before dial when no dial tone is detected

If dial tone detection = off, pause at this setting before dialing.

Duration time of Busy tone detect on [Min]

MIN time to detect BUSY TONE ON.
When it is shorter than the set value, the product does not judge it as a busy tone.

Busy tone detection on duration [maximum]

Maximum time to detect BUSY TONE ON.
When it is longer than the set value, the product does not judge it as a busy tone.

Busy tone detection off duration [minimum]

Duration time to detect BUSY TONE OFF
When a BUSY TONE OFF TIME longer than the set value is detected, counts it as a single busy tone. It does not count when the OFF TIME is shorter.

Busy tone detection off duration [maximum]

If the off time is longer than this, it is determined that the busy tone signal has disappeared.
(Busy tone signal count is reset)

Normal/Long

Check level for line training.
When set to Long, performs the training of line condition harder. (It becomes easy to feed back)

75 ms/1 sec

Sets a signal interval time for CED and DIS transmitted when receiving.
change this to 1s to disable the echo suppressor when communicating with overseas.

Rate/Line

Switching of No-ECM reception error judgment mode.
Select the number of error lines or the error line rate.
* Change the settings for 083 and 084/085 as a set.
e.g.)
082 Mode = Rate & 084 Rate = value, or 082 Mode = Line & 084 Rate = value

0 line
64 line
128 line
192 line
256 line
1024 line
2048 line

When this set value is exceeded during receiving, the product judges an excess error to disconnect the line.
* “0 line” operates with the internal initial value = “128 line”.

0 %
5 %
10 %
15 %
20 %

When this set value is exceeded during receiving, the product judges an excess error to disconnect the line.
* “0%” operates with the internal initial value = “10%”.

Disable
A4
A4/B4
A4/B4/A3

Used to disable color reception.
“Disable”: Drops the color reception capability bit from the DIS signal (which declares the capability of the own device) transmitted at the time of an incoming call. Since the transmitting side has no color receiving capability, it does not perform color transmission.
"A4" / "A4 / B4":  When "B4 / A3" / "A3" paper is enabled by fax, the color reception capability bit is dropped from the DIS signal (which declares the capability of the machine itself) sent at the time of an incoming call.

A4
A4/B4
A4/B4/A3
Auto

Use this when you want to specify a fixed paper width for fax reception regardless of the paper size set in the device.
If it is changed, the receiving paper width capability bit of the DIS signal (to declare the capability of the own device) transmitted at the time of the incoming call changes.

Example of use)

• When transmitting an A3 / B4 manuscript on the transmitting side, look at the receiving paper width capability bit of the DIS signal of the receiver (declare the capability of your device), and send it in A3 / B4 width or reduce it. Decide if you want to. If the receiving paper width capability bit = A4, reduce / cut to A4 and send.
• When A3 / B4 paper is not set in the device, but you want to receive faxes in A3 / B4 and receive it as A3 / B4 size electronic data by saving / transferring to external memory. Use for, etc.

When the received page length exceeds this value, forcibly finishes the receiving.

Reduction Send
CutOut Send LEFT
CutOut Send CENTER
CutOut Send RIGHT

Reduction
Send

Used when page width differs between the sender and receiver.
Reduction Send = Reduction send
CutOut Send LEFT = Cut at the left end and send at full size
CutOut Send CENTER = Cut at both ends and send at full size
CutOut Send RIGHT = Cut at the right end and send at full size

V.29 Tone for echo suppressor

On/Off

Adds an EP TONE when sending V29 9600/7200bps.
Used when a communication error has occurred due to a line echo in overseas communication.

Transmission start method (ignoring the first DIS)

Ignores the first DIS and starts receiving from the 2nd DIS when sending.
Used when a communication error has occurred in overseas communication due to the effect of a repeat echo or the like.

Select RTC signal [EOL × 6 / EOL × 12] at the end of the PIX signal (switch from high speed to low speed)

Until Detect Always

Until Detect: The monitor turns on when making a call and turns off when a fax signal is detected.
Always: The monitor is always on. You can listen to the fax communication signal from the monitor speaker, so you can use it when investigating problems such as line failures.
* Don't forget to return to the original state after confirming the trouble.

V.27ter
V.17
V.29
V.34

Interlocked with “communication mode” in fax settings.
ECM is required for V.34.

MH
MR
MMR

On/Off

Interlocked with “error correction mode (ECM)” in fax settings.
If ECM is turned off, V.34/MMR/Color communication are disabled.

100 ms
200 ms
500 ms

Adjusts signal intervals for procedure signals.
Used when an error occurs during communication procedure due to line echo/delay etc.

It may be useful to adjust this when a communication data error occurs.
Since optical line etc. have a highly level in general, lower this value when setting(e.g. -10 → -11, -12, -13).

-48 dBm
-43 dBm
-38 dBm
-33 dBm

If line noise is high during the occurrence of communication error, lower the detection range (e.g. -43 dBm --> -38 dBm, -33 dBm) may improve the symptom.

0 dB
1.8 dB
3.6 dB
7.2 dB

0 dB
1.8 dB
3.6 dB
7.2 dB

2400 bps
4800 bps
7200 bps
9600 bps
TC7200 bps
TC9600 bps
12000 bps
14400 bps

2400 bps
4800 bps
7200 bps
9600 bps
TC7200 bps
TC9600 bps
12000 bps
14400 bps

2400 bps
4800 bps
7200 bps
9600 bps
12000 bps
14400 bps
16800 bps
19200 bps
21600 bps
24000 bps
26400 bps
28800 bps
31200 bps
33600 bps

2400 bps
4800 bps
7200 bps
9600 bps
12000 bps
14400 bps
16800 bps
19200 bps
21600 bps
24000 bps
26400 bps
28800 bps
31200 bps
33600 bps

2400 sym/s
2800 sym/s
3000 sym/s
3200 sym/s
3429 sym/s

2400 sym/s
2800 sym/s
3000 sym/s
3200 sym/s
3429 sym/s

3429
sym/s